#ECU MAPPING PROGRAM SOFTWARE#
#ECU MAPPING PROGRAM SERIES#

Once the system built the selected tune file, wait for 30 seconds and then press the button вЂDownloadвЂ™ to save the file to the computer. If any issues are there, raise a ticket and they will help you in this by providing an engineerвЂ™s look at it. Select the tuning profile, DPF, or EGR switches and then confirm. Once the file gets uploaded, you will be given options for the original file. Navigate to the вЂBuild your TuneвЂ™ to complete the steps of uploading the original ECU file that will be used to get modified to the desired calibration. Then you will get access to a section called the вЂBuild your TuneвЂ™ section and with a credit balance that is positive, you get access to all the areas of a website. вЂPurchase CreditsвЂ™ has to be selected from the main page and the steps have to be followed to complete checkout. Before that check Wiki for seeing expert notes related to the ECU. Using the selected tool, read Original File from the ECUДownload the Original file of the ECU file from вЂECUвЂ™ by following the instructions of the tuning tool. A look-up service is also in process of getting created by them.Д¤. PrecisionCode.Works do support all the formats of master flash tools like BDM, Tricore (TPROT included), and OBD. You can also take a look on Amazon and eBay for comparing prize. Before that check Wiki to identify any known problems related to the tuning of ECU.Д®xtensive quantities of information will be available there on each of various tools and also supported types of ECU. This aids you in selecting the tuning method and also the best-suited tooling. Check in the drop-down menu to find the vehicleвЂ™s ECU type. WorkвЂ™s Tuner accountДЄfter logging in, navigate to Protocol Database.

And it takes only a few steps for using the ECU tune file service of PrecisionCode. The build time is an average of thirty seconds. The Precisioncode has facilitated calibration, DPF solutions, EGR solutions, Calculator for fuel economy, Actual Map View, tuning to 100вЂ™s of components. The services are available for both petrol and diesel vehicles.

#ECU MAPPING PROGRAM SOFTWARE#

They have created the software with utmost care and responsibility. The re-mapping is done so effectively that you wonвЂ™t have any complaints later. Using ECU Re-mapping Software, you can receive an e-mapped tuning file, that too in a few seconds. Worried about managing them? PrecisionCode has come with the best ECU software that comes with two benefits. It ensures the performance and efficiency of your vehicle. Thus, it is understood that the ECU plays a big part in your vehicle management properly. Turbo boost вЂ“ The amount of boost to be used and at what RPM.Valve timing вЂ“ Decides when the inlet should be opened and also the exhaust valveвЂ™s opening time.Ignition вЂ“ Decides when the spark should be fired in the petrol engine or when to inject fuel in the diesel.Fuel вЂ“ The amount to put in as a response to throttle and load.Air Intake вЂ“ The amount of air that should be allowed into the engine as a response to throttle.The ECU controls different factors like the following : The most important point is that the re-mapping of a vehicle does not have any negative effect on the life of the engine or exhaust emissions. Greater response, more power, and lesser fuel consumption come as one among many advantages that the remap offers. Remapping of the engine can enable the lifting of few restrictions forced on the vehicle by the manufacturer.Д®CU re-mapping removes the blocks on a few of manufacturersвЂ™ restrictions and facilitates the vehicle to perform like how it did when was designed originally. So the introduction of ECU is quite commendable. It takes only a few seconds or a maximum of minutes for the process. Moreover, the time consumed for bringing the values back to the proper ones has become really low. The process of calibration and re-calibration has become really easy. Its introduction has brought great changes into the field. But the ECU or Engine Control Unit has simplified the entire process. Setting the ignition time, air-fuel mixture, and idle speed in that way is very difficult.ДЄlso, the dynamic nature of controlling was restricted. The data is interpreted using look-up tables or performance maps that are multidimensional and the engine actuators are adjusted accordingly.Д«efore the ECU, ignition timing, air-fuel mixture, and also idle speed were set on a mechanical basis and controlled dynamically using pneumatic and mechanical means.

This is done by reading values got from many sensors that are kept inside the engine bay.

#ECU MAPPING PROGRAM SERIES#

ECU or an engine control unit is a kind of control unit that operates electrically and controls a series of actuators in a combustion engine inside so that the engine performance will get optimized.

Ecu mapping program